DALI Extension for 10 Devices

The DALI Extension is designed to integrate lighting devices with DALI interface.

With this DALI Extension up to 10 DALI devices in up to 16 groups can be controlled.

It is DALI-2 certified, offering features like expanded support for more devices, including sensors and switches.

Datasheet DALI Extension for 10 Devices

Using the DALI Alliance database, you can check which functions specific DALI devices support and what certifications they have.

Table of Contents

• Commissioning
• Pairing DALI devices
• DALI Broadcast
• Address conflict
• Create DALI groups
• Diagnostics for DALI devices
• Supported DALI device types
• Supported DALI-2 Instance Types
• Safety Instructions
• Documents

Commissioning↑

The DALI Extension is installed on a DIN rail in a suitable enclosure.

Connect the power supply, Link communication to the Miniserver and the DALI data lines.

DALI bus topology can be daisy-chained, star or tree. Ring topology is not permitted.

The maximum cable length of the DALI bus is 300m using 1.5 mm² (AWG16) conductors.
When using the maximum cable length, it is recommend to run DALI separate from any line voltage cables.
The maximum voltage drop must not exceed 2V.

The DALI Extension is equipped with a power supply for the DALI bus. If an external power supply is used, it is imperative that the correct polarity of the bus lines is observed. Also the supply of the DALI bus has to be deactivated in the properties of the DALI Extension in Loxone Config.

The Extension starts after switching on the power supply, and the status LED will flash orange after a short time when the connection to the Miniserver is established.

Then follow the pairing procedure on the Link Interface.

Pairing DALI devices↑

To search for DALI devices, first click on the DALI Extension in Loxone Config, and then activate DALI Device Search.

For a new installation, the checkbox "New Installation" must be activated, this will re-adress all DALI devices during the search.

If the DALI Extension is added to an existing DALI installation, a normal search is sufficient to find all DALI devices and their settings.
If a DALI device is added to an existing installation, a normal search is also sufficient. Available addresses are assigned to the new devices. To avoid possible address conflicts, the newly added devices must not have an assigned address yet.

It is recommended to supply all DALI devices with power during pairing, otherwise conflicts may occur.

Start the search with "Start Search" and all connected DALI devices that are not yet part of the program will be listed:

If the search was completed and you select a device here, it will identify itself, as all the outputs of the device start pulsing. This allows you to assign and name the devices correctly.

Select the desired device, assign a name, room and installation location and add it to the programming using the + button.

The right window lists all the devices that are currently part of the program. You can display them by clicking the button Show my DALI devices. You can also replace an existing device with a new device of the same type that was found in the search. This is useful when a device needs to be replaced or devices are added to a pre-configured program. Select the device to be added and the device to be replaced. By clicking on the button with the arrow pointing right, the old device is replaced with the new one in the program.

To apply the changes, save the program in the Miniserver.

Now the added devices are ready for use and the functions are available in the Periphery Tree in Loxone Config.

DALI Broadcast↑

Using a DALI broadcast, you can effortlessly control all compatible DALI bus devices at once, without the need for individual pairing or programming. To enable this feature, simply activate the Broadcast Application in the DALI settings.

Address conflict↑

If an address conflict is detected, e.g. if two or more devices have the same address, the function "Resolve Address Conflict" can be used:

The affected devices are assigned a new address. If devices were already paired, they can be added again and the old devices replaced. To do this, select the newly addressed device and the device to be replaced and click on the button with the arrow pointing right.

Alternatively, you can also start a search with "New Installation", where all device addresses are deleted and reassigned.

Create DALI groups↑

If several DALI lights are to be controlled simultaneously, a DALI group is recommended.
This offers the advantage that the programming is simpler and there is no time delay when dimming the lights. Also, central functions can be handled easier.

When pairing DALI devices, existing group assignments are imported and created in Loxone Config.

To create a new group, the DALI devices must already be paired.

The devices can be selected in the DALI group's properties, thus assigning them to that group.

The group actuator can then be used in programming.

Diagnostics for DALI devices↑

With the function "Activate all" all connected DALI lights are set to full brightness, so the wiring can be checked.

The option Display diagnostic inputs can be used to display an error input for DALI devices, that is active in case of errors.

Possible errors are: no bulb or defective bulb in the DALI device.

The DALI Monitor provides an analysis of the communication between the DALI Extension and devices. First connect to the Miniserver, click on the DALI Extension, and then on DALI Monitor.

The DALI Monitor displays the name of the device, the transmitted values and the DALI commands.

These are defined in IEC 62386-102, the following is an excerpt:

Supported DALI device types↑

Supported DALI-2 Instance Types↑

Safety Instructions↑

Installation must be carried out by a qualified electrician in accordance with the applicable regulations.

This device must be mounted on a DIN rail in an electrical distribution enclosure to ensure protection against contact, water and dust.

Documents↑

Datasheet DALI Extension for 10 Devices